Designing Headphne

Create T-Spline Body

Model Toolbar > Create > Create Form

Click OK

Sculpt Toolbar > Create > Box

Pick the left plane

Hover cursor over to center and pick a point

Drag out to about 50 x 50 and pick a point

Lehgth: 50  Width: 50  Height: 25
Symmetry: Mirror
Tick Length Symmetry and Width Symmetry
Click OK

Double-click on the vertical ring to loop them

ViewCube > Right

Right-click anywhere and select Edit Form

Drag the horizontal line of the manipulator up to about 1 grid
Click OK

Double-click on the horizontal line to loop them

Right-click anywhere and select Edit Form

Drag the vertical line of the manipulator to left 1 grid
Click OK

Shift + Mouse Wheel to orbit the body to check

Ctrl + Select the 4 faces

Right-click anywhere and select Edit Form

Manipulator Functions

Hover over the center node to display the 3 triangle

Alt + Drag (flatten) in to about 0.7

Alt + Drag (extrude) the arrow out to 15

Alt + Drag the center node in about 0.8

Alt + Drag the front arrow out to 5
Click OK

Ctrl + Select the bottom 2 faces, right-click and select Edit Form.
If the top 2 faces become green
Toolbar > Symmetry > Clear Symmetry

Alt + Drag the center node in about 0.9

Alt + Drag the arrow in -5
Click outside to deselect the faces

Pick the top-left face
Drag the rotation node up to -20 deg

Repeat the same steps on the top-right face to make a smiling face

Orbit the body to back
Ctrl + Select the 4 faces

Right-click and select Edit Form

Alt + Drag the center node in to 0.8

Alt + Drag the center node in to 0.7

Orbit the body and select the arrow
Alt + Drag the arrow in 15
Click OK

Insert Edge

Orbit the body
Double-click the center ring to loop them

Toolbar > Modify > Insert Edge

Additional ring added on left in green color
Change the distance to 0.4
Click OK

Pick a face

Shift + Double-click on the next face

This will loop the faces in the direction of second selected face

Right-click and select Edit Form

Alt + Drag the center node out 1.05

ViewCube > Front
Drag the vertical line of manipulator to right 1.5
Click OK

Crease Edge

Orbit the body

Toolbar > Modify > Crease

Double-click the back edge to loop all the edges and click OK

Ctrl + Select the top 2 faces, right-click and select Edit Form.

Alt + Drag the center node in 0.8

Alt + Drag the top arrow up 20

Orbit the body
Ctrl + Select the 2 side faces and drag the vertical line in 0.7

Drag the vertical line of the manipulator to right 0.7

Drag the arrow up to 4

Drag the rotation node to left 5 deg

ViewCube > Front
Drag the right arrow to 70

Drag the rotation node to right 6 deg

Mirror - Duplicate

Toolbar > Symmetry > Mirror - Duplicate

Turn on the orgin

Browser - Body

Pick the plane parallel to the body

2D Sketch

Toolbar > Sketch > Arc - 3-Point Arc

Pick 1st point on right

Pick 2nd point on left

3rd point to the height 100

Click Stop Sketch

Create Bridge

Toolbar > Modify > Bridge

Select the 2 top faces

Click the arrow of Side Two, then select the 2 faces on the other body

Click Follow Curve

Select the arc, click Preview

Click OK

ViewCube > Front
Turn off the sketch

Cross-select the bridge and right-click, select Edit Form.

Drag the arrow up to 40 and click OK

Orbit the headphone to show the bottom, Ctrl + Select 3 faces.
Right-click and select Edit Form

ViewCube > Front
Drag the horizontal line down 0.6

Select the front face, right-click and select Edit Form.

Drag the left arrow to 10 and click OK

Orbit to back, select the face and drag to right 10 and click OK.

Convert to Solid

Select the body

Toolbar > Utilities > Convert

Click OK

Create Hole

Toolbar > Construct > Offset Plane

Pick the X-Plane, drag the arrow up 160, click OK.

Toolbar > Sketch > Ellipse

Pick the top plane

Pick the center point

Move cursor to right until 60 and pick a point

Enter 20 for the vertical axis

Click Stop Sketch

Turn on the sketch

Ctrl + Select the ellipses, right-clcik and select Edit Form.

Pick inside and select the profile

Operation: Cut

Drag the arrow down to cut the body and click OK

Add Fillet

Toolbar > Modify > Fillet

Select the edge, enter 3 for the radius, click OK.

Orbit to bottom
Repeat the same steps

Appearances

Ctrl + Select the faces

Toolbar > Modify > Appearance

Apply To: Faces
Library: Fusion 360 Appearances/ Plastic/  Opaque/ Plastic - Matte (Gray)

Drag & drop the material on the face

Ctrl + Select the faces of bridge and ear set

Right-click and select Appearance

Darg & drop material Plastic - Glossy (Blue)

Ctrl + Select all faces on edge
Drag & drop material Plastic - Glossy (Red)

Ctrl + Select the inner faces of ear set
Click the arrow to download the material Fabric (Generic)
Drag & drop the material on the selected face